Ever wondered which makes the best – when it comes to build and amplifier ? A Mosfet or a Bipolar transistor ? Lets go through this article which compares both pros and cons of this dilemma. Most people in general never care about this as long as they get a satisfactory output performance. Lets first go through some Mosfet amplifiers – thats a list of mosfet amplifier circuits for many output variations, say 10 watts, 18 watts and 50 watts. Okay! Now lets go through another list of  Transistor amplifiers - which lists many amplifier circuits built using bipolar transistors. Now that should give you a rough idea and freshen up the concepts. Lets come to the point then, we are talking about a comparison between Mosfet and Bipolar designs in amplifiers. Well as per many read more

If you enjoyed this post, make sure you subscribe to my RSS feed!

The objective of this construction project is to build simple and easy to use test gadget that can be used to identify good and bad IC TIMERS from a given lot. Like opamps, an IC timer is another widely used electronic device and it finds its place in almost every project of hobbyists’ interest. This gadget not only enables you test the IC timer 555, it will also give you an opportunity to appreciate the tremendous functional potential of the various terminals of this truly versatile IC. Most of the circuits appearing in various magazines or books to test IC timers do the same by wiring the IC in one particular configuration only. Testing the IC timer with the gadget being described here not only tests the IC in all basic configurations, it practically tests the functionality of read more

If you enjoyed this post, make sure you subscribe to my RSS feed!

Thyristors (SCRs, Triacs) are very popular in AC power control applications where they are used to provide an active control of the AC power being fed to the load. The load here could be anything that is operated from AC mains and whose parameter to be controlled happens to depend upon the amount of AC power. Speed of motors, Temperature of heating elements etc are some of the examples. Here, we would build a simple circuit to demonstrate separately the use of SCRs and Triacs to provide AC power control. SCRs are used for those loads where it is immaterial whether the load current is unidirectional or bidirectional (though the AC input is always bidirectional). Heating element is one such load, an incandescent bulb is another. Remember that amount of heat is always proportional to read more

If you enjoyed this post, make sure you subscribe to my RSS feed!

Under previous posts, we have already seen how a bipolar transistor, NPN or PNP, can be used as a single pole, single throw switch. The transistor operating in saturation region with voltage across the switch being about 0.2 volt represents the ON-condition of the switch. The transistor operating in the cut-off region, where the only current that can flow through the switch is the collector-to-emitter leakage current represents the OFF-condition of the switch. We also demonstrated how an SCR can be used as a single pole single throw switch of the latching type. Another very important solid state device that can be usd as a switch in a way similar to the operation of a bipolar transistor is the Metal Oxide Semiconductor Field Effect Transistor (MOSFET) briefly mentioned in the last read more

If you enjoyed this post, make sure you subscribe to my RSS feed!

The objective of this simple exercise is to demonstrate the operation of solid state (or electronic) switches using electronic devices like TRANSISTORS or SCRs. There are many more electronic devices that can be used for the purpose. We have chosen these two as these are the most commonly used ones in this role, more so in the electronics circuits of hobbyists’ interest. MOSFET (Metal Oxide Semiconductor Field Effect Transistor) is another commonly used switching device that has outclassed bipolar junction transistors in many switching applications. It is not covered here but is separately covered in the next project. CIRCUIT DESCRIPTION The first part of the circuit starting from extreme left and comprising of Resistors R1, R2, Switch SW1, LED-1 and Transistor Q1 illustrates the read more

If you enjoyed this post, make sure you subscribe to my RSS feed!

Majority of Electronics enthusiasts and hobbyists wants to build their own AC-DC power supplies to test the electronics circuits built by them. The objective of this easy to build and understand circuit is to familiarise the constructor or the hobbyist with the effect of changing the rectifier-filter configuration on the DC output voltage produced in a conventional mains operable AC/ DC power supply. By opening or closing an appropriate combination of switches (SW-1 toSW-9 in the circuit diagram), this circuit could be configured into any one of the popular power supply rectifier circuits like (i) Conventional Half Wave Rectifier with positive DC output voltage (ii) Conventional Half Wave Rectifier with negative DC output voltage (iii) Conventional Full Wave Rectifier with positive read more

If you enjoyed this post, make sure you subscribe to my RSS feed!

The losses occurring in a d.c. motor are the same as in a d.c. generator  (i) copper losses (ii) Iron losses or magnetic losses (iii) mechanical losses As in a generator, these losses cause (a) an increase of machine temperature and (b) reduction in the efficiency of the d.c. motor. The following points may be noted: (i) Apart from armature Cu loss, field Cu loss and brush contact loss, Cu losses also occur in interpoles (commutating poles) and compensating windings. Since these windings carry armature current (Ia), Loss in interpole winding = Ia 2× Resistance of interpole winding Loss in compensating winding = Ia 2× Resistance of compensating winding (ii) Since d.c. machines (generators or motors) are generally operated at constant flux density and constant speed, the iron losses read more

If you enjoyed this post, make sure you subscribe to my RSS feed!

Since the armature of a motor is the same as that of a generator, the current from the supply line must divide and pass through the paths of the armature windings. In order to produce unidirectional force (or torque) on the armature conductors of a motor, the conductors under any pole must carry the current in the same direction at all times. This is illustrated in Fig. (4.10). In this case, the current flows away from the observer in the conductors under the N-pole and towards the observer in the conductors under the S-pole. Therefore, when a conductor moves from the influence of N-pole to that of S-pole, the direction of current in the conductor must be reversed. This is termed as commutation. The function of the commutator and the brush gear in a d.c. motor is to cause the reversal read more

If you enjoyed this post, make sure you subscribe to my RSS feed!